• その他のフルークグループ:
  • Fluke
  • Fluke Biomedical
  • Fluke Networks
  • Fluke Process Instruments
フルークブランドをさらに表示
Accelix Amprobe Beha-Amprobe Comark Emaint Landauer Pacific Laser Systems Pomona RaySafe Schad
ホーム
Precision, Performance, Confidence.
フルーク・キャリブレーション - Fluke Calibration Japan
  • 登録
  • ログ・イン
  • Contact Us

JP - Japanese (日本語) [Change]

 

6270A Embedded Software, Update by Serial RS-232 Port

Click here to update by USB.

TITLE USE WITH
6270A 6270A

The updating of embedded software should only be performed after given specific instructions to do so from Technical Support or a Fluke Calibration Authorized Service Center.

If the update isn't performed properly, your product may be inoperable until it is.

Instructions to update by the RS-232 serial port on the rear panel of the 6270A

The below procedure updates the main firmware. Updating the PCM (Pressure Control Module) firmware is not possible by the RS-232 serial port on the rear panel of the 6270A. PCM firmware update is possible by the USB firmware method (link to that web page is above). It is also possible if you have a PMM Calibration Kit (KIT-PMM-CAL-20M, KIT-PMM-CAL-40M or KIT-PMM-CAL-100M. If so, contact Fluke Calibration Pressure Technical Support for instructions.

Extract the two files to a location on your computer:

  • 6270A_###.img firmware file (### is the version number)
  • Download7.exe (version 2.0)

Note: If the CPU does not have any firmware on it then if must be flashed by the USB port method to be later updated by the serial RS-232 port method.

Connect a null modem RS-232 serial cable (pins 2 and 3 are crossed) to the back panel RS-232 connector on the 6270A and to the computer.

In the 6270A menu path: ‹Setup›, ‹Instrument Setup›, ‹Remote Port›, ‹RS-232 port›, ensure that the COM settings are Data Bits 8, Stop Bits 1, Flow Control None, Parity None, Baud 9600, EOL CRLF, Remote IF Terminal.

Open the Download7.exe software, choose the COM port on the computer in the drop-down list, and verify the COM port settings. Leave the “Fast” checkbox checked. Then click the [OK] button in the Download7 software.

Select the 6270A_###.img firmware file (### is the version number). Double-click it, or select it and press the [Open] button. The update will initialize and then run to completion.

When complete, turn off the 6270A controller by the main power switch on the back panel. Leave it off for one minute then turn it back on.

Wait for the controller to completely power up to the main screen, then go to the ‹Setup›, ‹Instrument Setup›, ‹About This Instrument› screen and verify that "Revision" is correct. Press ‹Exit› to return to the main screen.

More detailed instructions are in the 6270A Service Manual and on our Online Help Center.

Updates Include:

Main Version 1.10 (2020 Feb 10)
Fix: (OMA-676) Prevent error when exercising to minimum with absolute PMM
Fix: (OMA-677) Show PM500 C0 coefficient as psi value (not kPa)
Fix: (OMA-703) GPIB correctly asserting SRQ
Fix: (OMA-704) Prevent low pressure PM500 module overrange error
Fix: (OMA-725) Manual AutoZero values immediately saved to PMM non-volatile memory
Add: (OMA-733) Added Message Available (MAV) detection for GPIB communications
Add: (OMA-729) Allow changing External Driver duty cycle with command, OUTPut: SOLenoid<n>: DCYCLE
(OMA-7XX) Emulation mode improvements

Main Version 1.09 (Internal Release Only)
Main Version 1.08 (2019 Aug 12)
Fix: (OMA-675) Add delay between GPIB commands
Fix: (OMA-678) Prevent blank values on various screens
Fix: (OMA-633) Manual entry atm value showing as main pressure value at vent
Main Version 1.07 (2018 Oct 18)
Fix: (OMA-662) Prevent overshoot in absolute mode from low pressure to higher pressure setpoint 
Add: (OMA-663) Support CPS-40M
Fix: (OMA-633) Manual entry atm value showing as main pressure value at vent 
Fix: (OMA-617) Emulation mode improvements
Fix: (OMA-653) CPS function issue
Fix: (OMA-588) Absolute module grayed out in module selection screen
Fix: (OMA-642) Status field of the STAT, PR and PRR responses were always '0'
Fix: (OMA-631) Controller becomes non-responsive during PMM calibration routine
Fix: (OMA-622) Out of Range or Low Limit Exceeded error in Tare mode
Change: (OMA-614) Change default value of manual atmosphere uncertainty to 3.5 kPa
Fix: (OMA-601) Positive leak shows as negative value in leak test routine
Fix/Add/Change (Various): Emulation mode improvements
GUI Version 1.07 (2018 Oct 18)
Change: Update for main firmware changes
PCM Version 1.03 (2018 Oct 18)
Add: Support CPS-40M
Main Version 1.06 (2018 March 21)
Add: (OMA-589) Change message text to red when door is opened, “Please wait until done venting”

Add: (OMA-620) Support PM500 Pressure Measurement Modules, and zeroing of low absolute models

Fix: (OMA-623) Make LED on CPS brighter when the CPS is enabled and active

GUI Version 1.06 (2018 March 21)
Change: Update for main firmware changes, and match main version number
Main Version 1.05 (2017 September 25)
Fix: (OMA-569) Prevent error message when venting in absolute mode
Add: (OMA-581) Verify valve status before continuing after switching measurement modules, prevent overrange error
Fix: (OMA-598) Unit emulation command returned custom unit 4
Add: (OMA-595) Added OUTP:STAT command in DPI 515 emulation mode
PCM Version 1.01 (2017 September 25)
Fix: (OMA-580) Prevent overshoot of next pressure set point after venting
Main Version 1.04 (2017 March 31)
Add: (OMA-582) Allow for future Firmware Updates over RS-232
Fix: (OMA-584) Atmosphere setting retained on power up
GUI Version 1.01 (2016 October 31)
Change: Update for main firmware changes
Main Version 1.03 (2016 October 31)
Fix: (OMA-567) Prevent overrange error if exercise task is run with MAX setting
Add: (OMA-568) Add status display during firmware update routine. Add verification and error recovery.
GUI Version 1.0 (2016 July 19)
Change: Update for main firmware changes
Main Version 1.02 (2016 July 19)
Add: (OMA-564) CPS setup screen shows available CPS options (non-LED / LED). Setup –› Instrument Setup –› CPS.
Main Version 1.01 (2016 June 17)
Fix: (OMA-478) Uncertainty calculation per Uncertainty Technical Note
Fix: (OMA-483) Ethernet settings retained on power cycle
Change: (OMA-507) Range selection based on uncertainty instead of range
Change: (OMA-457) Option for program to proceed fully automated or by user entry of UUT reading. Maximum number of steps and cycles per program is 99
Change: (OMA-508) Select AutoZero reference in absolute mode. Automatic AutoZero in gauge mode. View AutoZero (zOffset) value in coefficients screen or by remote command
Add: (OMA-499) Ready Tolerance can be entered in % range. Useful when using a multi-range system
Add: (OMA-335) Supports system stacking mode (multiple 6270A controllers)
Add: (OMA-493) Remote commands to read active range, uncertainty
Add: (OMA-468) Remote command to set valve drivers based on control setpoint (allows for set up of automated regulator switching system)
Add: (OMA-407) Show test and supply pressures when the door is open
Add: (OMA-439) Error notification when CPS enabled but not installed
Add: (OMA-465) Czeck and Slovak languages
Add: (OMA-402) Support PG7000 automated piston float
GUI Version 1.00 (2016 June 17)
Change: Update for firmware changes
Main Version 0.43 (2015 December 15)
Fix: (OMA-483) Ethernet settings not retained after power cycle
Fix: (OMA-487) Error 222 "Out of Range" when pressure is stable
Main Version 0.42 (2015 November 24)
Fix: (OMA-481) Error 521 "Pressure Overrange" with low range Pressure Measurement Modules
Main Version 0.41 (2015 November 4)
Add: (OMA-467) CPC emulation mode didn't accept PCS400 commands
Main Version 0.40 (2015 October 1)
Fix: (OMA-452) UNIT:LENGTH command not working to set a value
Fix: (OMA-452) ABORT command works but required reboot to restore normal operating condition
Fix: (OMA-455) 6270 not working as security password to change date/time
Fix: (OMA-456) CPC emulation not working with GPIB
Fix: (OMA-459) Autotune did not work
Main Version 0.39 (2015 July 24)
Initial release
GUI Version 0.03 (2015 July 24)
Initial release

  • ホーム
  • 製品
    • 新製品情報
    • 電気校正
      • 電気標準器
      • 電気校正器
      • ベンチ・マルチメーター
      • 電気校正ソフトウェア
    • RF 校正
      • RF リファレンス・ソース
      • RF 校正アクセサリー
      • RF 校正ソフトウェア
    • データ収集とテスト装置
      • ベンチ・マルチメーター
      • データ収集
      • ファンクションおよび波形ジェネレーター
      • データ収集ソフトウェア
    • 温度校正
      • ITS-90 温度標準器
        • ITS-90 定点セル
        • 標準白金抵抗温度計(SPRT)
        • メンテナンス装置
        • 液体窒素式比較校正装置
        • 抵抗ブリッジ
        • 標準抵抗器
      • 校正バス
        • 小型校正バス
        • 標準バス
        • 特殊アプリケーション用バス
        • バス用アクセサリー
        • バス・コントローラー
        • バス用温度媒体
        • カスタム温度校正バス
      • 工業用温度校正器
        • フィールド・メトロロジー・ウエル
        • メトロロジー・ウェル
        • ハンドヘルド・ドライウェル校正器
        • フィールド・ドライウエル
        • 超小型バス
        • 赤外線校正器
        • 熱電対炉
        • デュアル・ブロック・ドライウエル
        • ゼロ点ドライウエル
      • プローブ/センサー
        • 白金抵抗温度計 (PRT)
        • サーミスター
        • 標準熱電対
      • デジタル温度指示計
      • マルチファンクション校正器
      • 温度校正ソフトウェア
    • 湿度校正
      • 湿度校正器
      • 湿度データ・ロガー/モニター
    • 圧力校正
      • ピストン・ゲージ
        • NMI ピストン・ゲージ
        • 絶対圧ピストン・ゲージ
        • 高圧力ガス・ピストン・ゲージ
        • 油圧式ピストン・ゲージ
        • ピストン・ゲージ用アクセサリー
      • 圧力コントローラー/校正器
        • 低圧力コントローラー/校正器
        • 空気式圧力コントローラー/校正器
        • 高圧空気式コントローラー/校正器
        • 油圧式コントローラー/校正器
      • 圧力モニター
        • 低圧力計
        • デジタル圧力計
        • 基準圧力モニター
      • 重錘形圧力計
        • 空気式デッドウェイト・テスター
        • 油圧式デッドウェイト・テスター
        • 液圧式デッドウェイト・テスター
        • 高圧油圧式デッドウェイト・テスター
        • デッドウェイト・テスター用アクセサリー
      • 手動校正器、モニター
        • 圧力校正器
        • 空気圧の制御
        • 液体圧比較器/ポンプ
      • Handheld Pressure Calibrators
      • エア・データ・テスト
      • ラボ環境モニター
      • 圧力校正アクセサリ
      • 圧力校正カスタム・システム
      • 圧力校正ソフトウェア
    • 流量校正
      • 気体流量標準器
      • 気体流量アクセサリ
      • GFS 質量流量一次標準
      • 流量校正ソフトウェア
    • プロセス校正ツール
      • 温度校正器
        • ハンドヘルド温度校正器
        • ドライブロック校正器およびマイクロバス
        • 高精度デジタル温度計
        • 温度プローブ
        • 赤外線温度計校正器
        • データ・ロギング機能付き湿温度計
      • 圧力校正器
        • デジタル圧力校正器
        • ハンドヘルド圧力校正器
        • 重錘形圧力計
        • 高精度デジタル圧力計
        • 校正用ハンド・ポンプ
      • マルチファンクション校正器
      • mA ループ校正器
      • プロセス校正ソフトウェア
    • 校正ソフトウェア
      • MET/CAL ソフトウェア
      • MET/CAL Support
      • 資産管理ソフトウェア
      • 温度校正ソフトウェア
      • 圧力校正ソフトウェア
      • 流量校正ソフトウェア
      • 機械/寸法校正ソフトウェア
    • サービスとサポート
    • すべての校正機器
  • ご購入について
    • 購入窓口
    • 見積依頼
    • デモ依頼
    • 相談/問い合わせ
    • Certified Pre-Owned Equipment
    • General Services Administration (GSA)
    • Financing Program
    • National Stock Numbers (NSNs)
    • Payment Options and Tax Info
  • ニュース
    • プレスリリース
    • プロモーション
    • 業界リンク
    • Metrology Salary Survey
  • トレーニングとイベント
    • 展示会/セミナー
    • トレーニング・コース
    • User Group Meetings
    • ウェブセミナー
      • ライブ・セミナー
      • 過去のセミナー(アーカイブ)
  • カタログ・資料
    • Education Hub
    • About Calibration
    • 参考資料
    • 製品資料
    • 製品マニュアル(ユーザー・ガイド)
    • Videos and Virtual Demos
    • Blog
  • サービスとサポート
    • Service Request (RMA)
    • Service Plans
    • ナレッジベース
    • 認定校正
    • サービスセンター
    • Calibration Certificates
    • Community Forum
    • My MET/SUPPORT
      • Activate
      • Procedures
      • Software
      • Technical Bulletins
      • Priority Support
      • Manuals
    • 製品マニュアル(ユーザー・ガイド)
    • 製品の登録
    • 安全データ・シート(SDS)
    • 安全性および製品に関するお知らせ
    • ソフトウェア・ダウンロード
  • フルーク・キャリブレーション
    • お問い合わせ先
    • 所在地
    • キャリア
    • フルーク・キャリブレーションとは
      • Hart Scientific:温度校正
      • DH Instruments:圧力/流量校正
      • Pressurements:圧力校正
      • Ruska:圧力校正
    • 関連企業
    • 行動規範とコンプライアンス
    • よくある質問
ホーム|カタログ・関連資料|ソフトウェア・ダウンロード|ファームウェア|6270A Embedded Software, Update by Serial RS-232 Port

サイトの改善のため、フィードバックをお寄せください。
フィードバック・フォーム≫
©1995-2021 Fluke Corporation
             

Secondary menu

  • 免責事項
  • プライバシー・ステートメント
  • ウェブマスター
  • Terms of Use
  • Terms and Conditions of Sale